DIY Water Heater Installation
Installation Instructions for the Water Heater Hook-up Kit. Electric Water Heater. A WARNING. Important Follow the procedures outlined in the water heater manufacturer's installation manual to correctly install this water heater. Hot Waler Outlet. Shu-Off Valve. (Must be Open. During Heater. Operation). Cold Water Supply. Shop our selection of Install Kit, Water Heater Parts in the Plumbing Department at The Home Depot. Everbilt Electric Water Heater Installation Kit. Model# EBWCBEKIT Rheem PROTECH Pilot Assembly Replacement Kit for GE, Hot Point and Sure Comfort 22V4R0FN Ultra Low NOx Natural Gas Water Heaters. The water heater installation kit is used to install a new gas water heater or replace the existing connectors. The kit includes (2) in flexible water supply connectors, (1) in epoxy coated gas connector, (2) compression adapters, and (1) roll of sealing Teflon tape. Use this kit for a reliable installation. EASTMAN certified.
The kit features special push-fit fittings that allow the user to easily connect water distribution pipe. As the world leader in push-to-connect plumbing systems, SharkBite strives to innovate efficient plumbing solutions that improve performance and save time when installing new systems or making repairs.
We believe that it is our unwavering commitment to innovating new solutions for optimizing efficiency and reliability that make SharkBite a pioneer and the hallmark of push-to-connect plumbing solutions for plumbing professionals.
Our comprehensive range of plumbing fittings, water control valves and PEX pipe has made SharkBite the only total plumbing solution from meter to fixture.
No solder, unions, clamps or glue is required, improving repair and installation efficiency and minimizing lost time on the job. The SharkBite system lowers the chance of making errors, reducing potential leaks and customer callbacks. One manufacturer with a complete set of solutions for improving plumbing efficiency and getting the job done. Reviews Rated 5 out of 5 by Matt H from Water heater fittings This was one of the most easiest plumbing expierences I have had I'm for sure not a plumber link these shark bite fittings make it super easy Date published: Rated 5 out of 5 by Duane from I've use the SharkBite connections several times now.
I can't imagine doing any kind of plumbing I've use the SharkBite connections several times now.
Our comprehensive range of plumbing fittings, water link valves and PEX pipe has made SharkBite the only total plumbing solution from meter to fixture. Good afternoon, If the nipples coming off the Water Heater are galvanized pipe, then no. As long as you are below that, you won't have any issues.
I can't imagine doing any kind of plumbing without them. If you need to disconnect for some reason, that is very simple and then the connection goes right back together. Please see the link below. This is big Al againguess I didn't ask my question very well. Good afternoon, You should contact the water heater manufacturer to see if there would be any issues adding a male threaded adapter to your machine and removing their nipple off. In regards to temperature, our fittings can withstand up to degrees Fahrenheit.
As long as you are below that, you won't have any issues. Good afternoon, If the nipples coming off the Water Heater are galvanized pipe, then no.
Brass and Galvanized pipe will become corrosive with each other once water is introduced.
Good Afternoon, To remove a SharkBite fitting, use the disconnect clip to depress the release collar and release the pipe from the fitting. Brass and Galvanized pipe will become corrosive with each other once water is introduced. I can't imagine doing any kind of plumbing
If the nipples are a metal that won't corrode when in contact with Brass and water, then yet. Can this fitting be used as a dielectric union?
How to install a hot water heater kit
Can it be connected to a galvanized pipe since it is made of brass? We do not recommend using our products with galvanized pipe. Should this fitting be installed onto the water heater nipples first and then slipped into place on the copper pipe or could Hot Water Heater Hook Up Kit install it on the pipe end first and then tighten it down onto the water heater since the joint rotates? Good morning, You can do either installation process.
If you connect the fitting to the pipe first, make sure you have enough play in the line to be able to fully thread the fitting onto the water heater. How do I use the disconnect clamp.
Good Afternoon, To remove a SharkBite fitting, use the disconnect clip to depress the release collar and release the pipe from the fitting. Below is a link to a youtube video that will show you how to disconnect the fitting from the pipe. Will the pipe connectors connect to existing copper tubing?
You can connect our SharkBite fittings to existing lines. You do not have to make it shine as if you were soldering, but you do want to make sure there isn't any gunk or build up on the pipe that could cause the teeth to slip or the o-ring to not seal completely.
How To's How To: